Cavalry Storage CADA-U32A Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Disková pole Cavalry Storage CADA-U32A. Cavalry Storage CADA-U32A User's Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 15
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
User’s Guide: CADA-U32A Series RAID Enclosure
This guide contains instructions for changing the RAID settings on your CADA-U32A
Series Personal Disk Array. If you need assistance, please contact customer service
at
[email protected]. The guide is structured as follows:
Product Diagrams - Page 2
RAID Settings Overview with Explanations - Page 3
Instructions for Changing RAID Settings - Page 4
1
Zobrazit stránku 0
1 2 3 4 5 6 ... 14 15

Shrnutí obsahu

Strany 1

User’s Guide: CADA-U32A Series RAID Enclosure This guide contains instructions for changing the RAID settings on your CADA-U32A Series Personal Di

Strany 2 - Diagrams

e. The drive will start partitioning as shown. It should take a minimum of 2 minutes to finish. f. You now have a MAC OS extended partition. We c

Strany 3 - RAID Settings Descriptions

g. The warning dialog for erasing the partition will pop up. Go ahead click “Remove”. h. Your drive is now clean of all partitions. Continue to S

Strany 4 - Changing RAID Settings

6. After the drive is completely uninitialized, turn off your drive. Set the CADA-U32 on its side. Remove the cover by removing the screws on the bot

Strany 5

7. Locate the “Jumper Block”. The Jumper Block consists of 6 Jumper Pins, with 4 pins being covered by two black “Jumper Shunts” at any given time.

Strany 6

8. Decide which RAID setting you want, and, following the diagram to the right, move the jumper shunts to cover the appropriate pins. (On the diagram

Strany 7

9. Your jumper block should look something like this when finished changing settings. Shown is RAID 0 (striping) with pins 1, 2, 5, and 6 covered. No

Strany 8

Diagrams Front View: 1. Power indicator 2. Rebuild indicator 3. HDD1 Access Indicator 4. HDD2 Access Indicator 5. HDD1 Error Indicator* 6. HDD2

Strany 9

RAID Settings Descriptions SINGLE MODE Array will show up as two independent drives. This function can be used if only if two different brands and

Strany 10

Changing RAID Settings 1. Start your computer and wait for your operating system to load completely. 2. Connect the square end of the USB 2.0 cabl

Strany 11

b. The Run dialog box will show up. Enter “cmd” in the text box then press the <ENTER> key. c. Virtual DOS command console window will s

Strany 12

d. Now to use DISKPART. Warning: Be careful not to select your system drive as you could erase it and your current Windows system! i. Type “list di

Strany 13

Mac OS X a. Go to top menu “Go” and select “Utilities”. The Utilities window opens. Select “Disk Utility” to start the disk utility program.

Strany 14

b. Click the header on the left which starts with the drive size in gigabytes (1). Now click on the “partition” tab on top (2). Disk Utility will swi

Strany 15

c. Now click on “Options” under the partition graph (1). The partition scheme type selection window will pop up. Make sure the selection is “Apple Pa

Komentáře k této Příručce

Žádné komentáře